Vehicles
48 not categorized PORSCHE 944 ENGINE SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.
$40.91
Make a selection
$123.30
Make a selection 54706308 Mounts on the rear engine sheetmetal View/Change Diagram
From $39.50
Make a selection 91450415810 Known as: engine compartment seal View/Change Diagram
$20.09
Make a selection
From $11.00
Make a selection
From $13.20
Make a selection 9A110232200
$14.50
Make a selection 9A110231200 Known as: gasket cyl. 1 - 3 View/Change Diagram
From $17.00
Make a selection 99970161340 Known as: round seal / round seal 20 x 5 View/Change Diagram
From $4.50
Make a selection 021101341A If you notice a strange oil leak at the base of your cylinders, this is the culprit! also used to space the cylinders when building a high performance engine. four required for all stock applications and multiples for high performance applications. View/Change Diagram
From $2.00
Make a selection 021105279 Resides in the front relief of the flywheel mounting surface and always overlooked, this graphite seal it the final part needed to keep the oil in the engine case one required View/Change Diagram
From $1.95
Make a selection 021119955 This is another one of those small sealing washers to insure that all of the cooling air is flowing over the engine and not out the open holes! order all of the other sealing washers at the same time like the spark plugs and the oil pressure switch grommet. View/Change Diagram
$5.25
Make a selection 021198009D You can’t rebuild without an engine gasket kit, even if you are reusing the hard parts! Remember in addition to order four baffle plate seals, a front and a rear main seal and maybe a couple of cv joint gaskets! General Fitment914 1970-76
$76.56
Make a selection 022101559S One of the most required and necessary-to-replace parts in any 914 engine rebuild. This plate is the seal that fits the baffle windage tray into the bottom of the engine case. Super high-temperature made from that latest silicone rubber technology. General Fitment914 1970-76
$17.38
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 10010303000TU Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders have extremely high thermal resistance and are nikasil coated to reduce wear and friction. We also have the piston rings (sealing and oil scrapers) pre-installed to ensure reliability. Each of our piston and cylinder kits are complete and ready for installation. Features: mahle forged 935 3.0 l turbo pistons mahle nikasil coated cylinders increased 7:1 compression = greater acceleration 95 mm pistons / 95 mm finned wr group 0 cylinders piston rings pre-installed piston pins and circlips are included complete set of 6 - ready for installation made in Germany we recommend the complete engine gas...(choose a part on the right to read more) General Fitment911 1970-73
From $6,197.50
Make a selection 022101559 One of the most required and necessary-to-replace parts in any 914 engine rebuild. This plate is the seal that fits the baffle windage tray into the bottom of the engine case. Super high-temperature made from that latest silicone rubber technology. Four required, sold each. View/Change Diagram
$4.77
Make a selection 106082 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05
$681.94
Make a selection 96410601402EQ This OEM cover sits low nearest the rear bumper. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend purchasing a new seal, part # 96410622301 and plug, part # 96410623701 to complete the installation. Sold individually. 1 necessary per car.
$601.70
Make a selection 13271016 For all the Porsche drivers looking to replace their old standard suspension in their used "987", or for anyone who would like to increase their driving dynamics, st suspension now have the st x coilovers available. In addition to the tested and continuous lowering of up to 60 mm (1.2"-2.4"), the st suspension developed by kw allows you to further increase the handling and excellent road holding of the mid-engine Porsche Boxster and Porsche Cayman.once installed, the st x coilover can be easily adjusted using a polyamide ring on the galvanized, multiple-sealed strut. Adjustment is different for each car, but typically you can expect between 35 and 65mm of lowering on both the front and rear axles. For lower...(choose a part on the right to read more) General FitmentBOXSTER 2005-08
$1,376.66
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |